2017年8月4日星期五

SMT Curing / Baking Oven for SMT Soldering

There are three types of Surface Mounting: Type 1, Type II and Type III.
For Type III surface mount, components glued to the bottom of the board require curing before wave soldering. In addition, electronic components placed on the solder paste in Type I and Type II Surface Mount Technology assemblies achieve reduced solder defects (such as solder balls) by being baked before reflow soldering.
SMT

In electronics, an oven is required for both adhesive curing and solder paste baking operations. The same or different ovens may be used for adhesive curing and baking of solder paste.
If an Infrared (IR) oven or a convection oven is used for reflow soldering, it is not necessary to have separate adhesive and solder paste baking ovens. The same IR or convection oven can be used for adhesive curing, solder paste baking, and reflow soldering.
The decision to combine solder paste baking, solder reflow and adhesive curing in the same oven depends on volume requirement. It also means that a decision has been made to use IR or convection instead of other reflow soldering processes such as vapor phase, laser soldering, or convection belt soldering. Today the convection oven is more widely used than any other type of oven for SMT.

SMT Repair and Inspection Equipment

Equipment unique to surface mounting includes inspection and repair / rework equipment. Inspection equipment for surface mounting in electronics has not matured yet. There are two main types of automated inspection equipment on the market: x-ray and laser. However, most electronic companies depend on visual inspection at 2 to 10X, using either microscope of magnifying lamp.
SMT

Repair / Rework equipment and electronic PCB assembly tools and equipments use conductive tips or hot air for removal and replacement of electronic components. Conductive tooling, such as soldering iron tip attachments, is very inexpensive. The tips come in different configurations for different electronic components but have limited applications.
At a slightly higher cost, there are other conductive tips with built-in heating elements.
At a much higher cost, hot air repair / rework tools are available that use nozzles of different sizes for components of different types and sizes. The hot air repair tooling is most commonly used for surface mounting in SMT because it is ideal for damage-free repair. (Check: SMD Soldering, BGA Soldering and Rework).
Even in-line (and expensive) repair systems are available on the market. However, when selecting repair / rework equipment, electronic companies must keep in mind that repair / rework tooling does not need to be an automated, expensive in-line system designed for high volume repair. If a large number of boards is to be repaired, automated repair equipment is not the answer. Instead, the process should be controlled to keep the defect rate low.

Lead-Free (Pb-Free) Solder and Composition

Lead-Free Solder: Solder with NO Lead (Pb). Lead-Free is taking rapid momentum around the world after the EU (European Union) Directives to wipe off lead (Poison) from electronic soldering considering its health and environmental effects
RoHS: Restriction of Hazardous Substances [ lead (Pb), mercury (Hg), cadmium (Cd), hexavalent chromium (CrVI), polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE).]
WEEE: Waste from Electrical and Electronic Equipments.
Lead-Free Solder

Why Lead Free in Electronics

Many of the electronic companies and manufacturers around the globe were using Tin-Lead (Sn/Pb) solder for PCB assembly and rework. They also used No-Clean Liquid Flux and No-Clean Solder Paste. They did not bother to clean the PCB and the flux residue after assembly. These boards were later dumped into earth.
While lead is dangerous and harmful during the assembly process, dumping the board in soil was harmful to the environment. This ultimately lead to make lead-free PCB assembly mandatory.

Lead-Free Solder

Various Chemistry for alloy composition in lead-free solder was explored. Several things had to be kept in mind:
  • Composition of lead-free cored solder wire for hand-soldering
  • Composition of solder bar for wave soldering
  • Composition of solder paste for reflow and hot air soldering
  • Composition of BGA Balls
  • Chemistry of flux to be used in lead-free soldering
  • Temperature resistance and tolerance of led-free compatible electronic components

BGA Rework / Repairing / Hand Soldering

Rework and hand soldering of BGA Packages is the toughest part. It needs practice to do the job. Let us understand Desoldering and soldering of BGA packages:

Desoldering BGA

The most common practice to desolder BGA is hot air. Here are the steps to desolder BGA Package using Hot Air:
  • Apply liquid solder flux on the sides of the package.
  • Preheat the package from both top and bottom. Heat can be given from the bottom using a preheated while heat from the top can be given using a Hot Air Rework System. Hakko FR-820 is the best available preheater while Hakko FR-803 is the best economical Hot Air SMD / BGA Rework System
  • Now using the correct BGA Nozzle, give heat on top of the BGA Package.
  • The solder balls underneath the BGA package will melt. Pick up the package with a Tweezer of using vacuum pick-up.
BGA

Soldering BGA

Again the most common practice to solder BGA is hot air. Here are the steps to solder BGA Package using Hot Air:
Once the BGA Package is removed, clean the pad and remove any excess solder from the board.
  • Apply Flux Paste (Not Liquid Flux) on to the pad. Paste flux will help solder balls to stick so that they do not fall or change position.
  • Place solder balls very carefully on the pad.
  • Apply paste flux to the bottom (soldering side) of the BGA package.
  • Carefully place the BGA Package of the solder balls.
  • Preheat and then apply Hot Air from both top and bottom.
  • Solder balls will melt and get soldered.
BGA technology and the BGA soldering is very reliable if done using the correct procedure. A BGA has less resistance to heat and hence there is lesser or no damage due to overheating.

SMT Dictionary – Surface Mount Technology Acronym and Abbreviation

SMT (Surface Mount Technology) is a packaging technology in electronics that mounts electronic components on the surface of a printed circuit board / Printed Wiring Board (PCB / PWB) instead of inserting them through holes of the board. SMT or Surface Mount Technology is relatively new technology in electronics and provides state-of-art, miniature electronics products at reduced weight, volume and cost.
History of SMT is rooted in the technology of Flat Packs (FP) and hybrids of 1950s and 1960s. But for all practical purposes, today’s SMT can be considered  to be a continually evolving technology. Currently the use of Fine Pitch, Ultra Fine Pitch (UFP) and Ball Grid Arrays (BGAs) are becoming even more common.
Even the next level of packaging technologies such as Chip-on-Board (COB), Tape-Automated Bonding (TAB), and Flip Chip Technologies are gaining widespread acceptance. Multichip Modules (MCMs) using wire bond, TAB, or Flip Chip are used to achieve the highest performance possible but with a cost premium.
SMT

Here I explain SMT acronyms and abbreviations.

SMT Dictionary

  • A-Stage: The condition of low molecular weight of a resin polymer during which the resin is readily soluble and fusible.
  • Anisotropic: A material fillet with a low concentration of large conductive particles designed to conduct electricity in the Z axis but not the X or Y axis. Also called Z axis adhesive.
  • Annular Ring: The conductive material around a drilled hole.
  • Aqueous Cleaning: A water-based cleaning methodology which may include the addition of the following chemicals: neutralizers, saponifiers, and surfactants. May also use DI (Deionized) water only.
  • Aspect Ratio: A ratio of the thickness of the board to its preplated diameter. A via hole with aspect ratio greater than 3 may be susceptible to cracking.
  • Azeotrope: A blend of two or more polar and non polar solvents that behaves as a single solvent or remove polar and nonpolar contaminants. It has one boiling point like any other single component solvent, but it boils at a lower temperature than either of its constituents. The constituents of the azeotrope cannot be separated.
  • B. Stage: Sheet material (e.g., glass fabric) impregnated with a resin cured to an intermediate stage.
  • Ball Grid Array (BGA): Integrated circuit package in which the input and output points are solder balls arranged in a grid pattern.
  • Blind Via: A via extended from an inner layer to the surface.
  • Blowhole: A large void in a solder connection created by rapid outgassing during the soldering process.
  • Bridge: Solder that bridges across two conductors that should not be electrically connected, thus causing an electrical short.
  • Buried Via: A via hole connecting internal layers that does not extend to the board surface.
  • Butt Joint: A surface mount device lead that is sheared, so that the end of the leads contacts the board and land pattern.
  • C-Stage Resin: A resin in a final stage of cure.
  • Capillary Action: The combination of force, adhesion, and cohesion which causes liquids such as molten metal to flow between closely spaced solid surfaces against the force of gravity.
  • Castellation: Metallized semicircular radial features on the edges of LCCC’s that interconnect conducting surfaces. Castellations are typically found on four edges of a leadless chip carrier. Each lies within the termination area for direct attachment to the land patterns.
  • CFC: Chlorinated fluorocarbon, cause depletion of ozone layer and scheduled for restricted use by the environmental protection agency. CFC’s are used in air conditioning, foam insulation and solvents, etc.
  • Characteristic Impedance: The voltage-to-current ratio in a propagation wave, i.e., the impedance which is offered to the wave at any point of the line. In printed wiring its value depends on the width of the conductor to ground plane(s) and the dielectric constant to the media between them.
  • Chip Component: Generic term for any two-terminal leadless surface mount passive devices, such as resistors and capacitors.
  • Chip-on-Board Technology: Generic term for any component assembly technology in which an unpackaged silicon die is mounted directly on the printed wiring board. Connections to the board can be made by wire bonding, tape automated bonding (TAB), or flip-chip bonding.

SMD Surface Mount Electronic Components for SMT

SMD or Surface Mount Electronic Components for SMT are no different from through-hole components as far as the electrical function is concerned. Because they are smaller, however, the SMCs (surface mount components) provide better electrical performance.
Not all components are available in surface mount for electronics at this time; hence the full benefits of surface mounting on  printed circuit board are not available, ad we are essentially limited to mix-and-match surface mount assemblies. The use of through-hole components such as pin grid array for high end processors and large connectors will keep the industry in mixed assembly mode for the foreseeable future.
SMD

Availability of Surface Mount Electronic Components

While only a few types of conventional DIP packages meet all the packaging requirements, the world of surface mount packages is vastly more complex.
The package types and package and lead configurations available are numerous. In addition, the requirements of surface mount components are far more demanding. SMCs must withstand the higher soldering temperatures and must be selected, places, and soldered more carefully to achieve acceptable manufacturing yield.
There are scores of components available for some electrical requirements, causing a serious problem of component proliferation. There are good standards for some components, whereas for others standards are inadequate or nonexistent. Some electronic components are available at a discount, and others carry a premium. While surface mount technology has matured, it is constantly evolving as well with the introduction of new packages. The electronics industry is making progress every day in resolving the economic, technical, and standardization issues with surface mount components. SMDs are available as both active and passive electronic components.

Passive Surface Mount Electronic Components

The world of passive surface mounting is somewhat simpler. Monolithic
ceramic capacitors, tantalum capacitors, and thick film resistors form the core group of passive SMD. The shapes are generally rectangular and cylindrical. The mass of the components is about 10 times lower than their through-hole counterparts.
The surface mount resistors and capacitors come in various case sizes to meet the needs of various applications in the electronics industry. While there is a trend toward shrinking case sizes, larger case sizes are also available if capacitance requirements are large. These devices/ components come in both rectangular and tubular (MELF: metal electrode leadless face) shapes.

Surface Mount Discrete Resistors

There are two main types of surface mount resistors: thick film and thin film.
Thick film surface mount resistors are constructed by screening resistive film (ruthenium dioxide based paste or similar material) on a flat, high purity alumina substrate surface as opposed to depositing resistive film on a round core as in axial resistors. The resistance value is obtained by varying the composition of resistive paste before screening and laser trimming the film after screening.
In thin film resistors the resistive element on a ceramic substrate with protective coating (glass passivation) on top and solderable terminations (tin-lead) on the sides. The terminations have an adhesion layer (silver deposited as thick film paste) on the ceramic substrate, and nickel barrier underplating followed by either dipped or plated solder coating. The nickel barrier is very important in preserving the solderability of terminations because it prevents leaching (dissolution) of the silver or gold electrode during soldering. Resistors come in 1/16, 1/10, 1/8 and ¼ watt ratings in 1 ohm to 100 megaohm resistance in various sizes and various tolerance. Commonly used sizes are: 0402, 0603, 0805, 1206, and 1210. A surface mount resistor has some form of colored resistive layer with protective coating on one side and generally a white base material on the other side. Thus the outer appearance offers a simple way to distinguish between resistors and capacitors.

Ball Grid Array (BGA) Package

Ball Grid Array or BGA is a surface-mount package (with no leads) utilizing an array of metal spheres (solder balls) for electrical interconnection. BGA solder balls are attached to a laminated substrate at the bottom of the package. The die of the BGA is connected to the substrate by wire bonding or flip-chip technology. The BGA substrate has internal conductive traces that route and connect the die-to-substrate bonds to the substrate-to-ball array bonds.
BGA is soldered on to the printed circuit board using a reflow oven. As the solder balls melts in the reflow oven, the surface tension of the molten solder ball keeps the package aligned in its proper location on the circuit board, until the solder cools and solidifies. Proper and controlled soldering process and temperature is essential for good solder joints and to prevent solder balls from shorting with each other.
BGA

Advantages of Ball Grid Array (BGA) Packaging
  • Ball Grid Array (BGA) offers several advantages over other electronic components. The most important advantage of BGA packaging for integrated circuits is its high interconnection density. BGA packages also lesser space on the circuit board.
  • Assembly of Ball Grid Array onto circuit boards is more efficient and manageable than its leaded counterparts because the solder needed for soldering the package onto the circuit board come from the solder balls itself. These solder balls also ‘self-align’ themselves during mounting
  • Lower thermal resistance between BGA Package and the circuit board is another advantage of Ball Grid Array packaging. This allows heat to flow more freely resulting in better heat dissipation and prevents the device from overheating.
  • BGA also offers better electrical conductivity because of shorter path between the die and the circuit board.
Disadvantages of BGA
Like all other electronic packages, BGA too, have some drawbacks. Following are some of the disadvantages of BGA:
  • BGA packages are more prone to stress because of flexural stress from the circuit board leading to potential reliability issues.
  • Inspecting of solder balls and solder joints for defects is very difficult once the BGA has been soldered onto the circuit board.