2017年8月4日星期五

Surface Mount Design Considerations in SMT & CTE Mismatching

There are many design issues that must be settled before a surface mount technology design or packaging direction is selected.
System analysts start with determining product needs in the marketplace. Therefore, the designer must look at the proposed product from the systems point of view. Great devices on printed circuit boards do not sell in the marketplace. Products sell. Therefore, the designer must consider market needs, function, and package moisture sensitivity. The product must also satisfy thermal and solder joints reliability requirements. As the packaging density increases, moreover, thermal problems are compounded, with a potential adverse impact on overall product reliability.
SMT

Solder joint reliability for surface mount is a source of concern because of CTE mismatch, between ceramic packages and PCB for SMT made from FR-4 glass epoxy substrates.
Because the plastic packages used in commercial applications have complaint
leads, they do not experience problems related to CTE mismatch. The large plastic packages, especially plastic ball grid arrays (PBGA), may be prone to cracking at reflow soldering temperatures, however, and this is an industry problem. Long-term solutions are still evolving, but baking before reflow soldering offers one answer.
The increase in SMD Electronic Components package density on board has necessitated the use of file lines at closer spacings. This can increase cross-talk between the lines, especially if they carry high speed signal. The product design is also influenced by the type of CAD system that is available. The cost or the schedule or both may be affected by the type of CAD system used for SMT PCB design.
Thus, for every SMT board, the designer must consider all the pros and cons of designing the board in SMT. In the decision is to go ahead with SMT, then it is important to follow the specific guidelines and rules.

BGA (Ball Grid Array): Repairing and Soldering BGA

BGA Soldering

During the initial stages, BGA technology was a matter of concern. People had doubts on solderability and reliability of BGA components. In BGA, the pads are under the device and not visible and hence it is necessary to ensure the correct process of soldering and inspection.
Today, BGA solder techniques is tried and tested and has been proved and trusted to be very reliable. It has also been learnt that once the process is set up correctly, BGA solder reliability is mush higher than that for quad flat packs (QFP) or any other SMD Package.
Reflow Soldering techniques is used to solder BGA. Reflow soldering technique is used to solder BGA because it helps the whole assembly to be brought up to a fixed temperature in order to melt the solder or solder balls underneath the BGA components.
For any BGA soldering, the solder balls on the package have controlled amount of solder. Solder ball in various sizes of 18 mil, 24, mil 30 mil etc are available. When the Board with the solder balls and BGA Package is placed in the reflow oven, it gets heated and the solder melts. Surface tension causes the molten solder to hold the package in the correct alignment with the circuit board. It in important to take care of the composition of the solder alloy and the soldering temperature so that the solder does not completely melt, but stays semi-solid , so that the solder balls stay separate from each other and do not result in any bridging.
BGA

Inspection of BGA solder joint

BGA inspection is one of the toughest jobs. It becomes extremely difficult to inspect the BGA joints since the solder is underneath the BGA Package and are not visible. The only satisfactory means of testing BGA Solder Joints is X-rays. X-Ray helps to see the joints underneath the package and thus helps in inspection.

BGA Rework / Repairing / Hand Soldering

Rework and hand soldering of BGA Packages is the toughest part. It needs practice to do the job. Let us understand Desoldering and soldering of BGA packages:

Desoldering BGA

The most common practice to desolder BGA is hot air. Here are the steps to desolder BGA Package using Hot Air:
  • Apply liquid solder flux on the sides of the package.
  • Preheat the package from both top and bottom. Heat can be given from the bottom using a preheated while heat from the top can be given using a Hot Air Rework System. Hakko FR-820 is the best available preheater while Hakko FR-803 is the best economical Hot Air SMD / BGA Rework System
  • Now using the correct BGA Nozzle, give heat on top of the BGA Package.
  • The solder balls underneath the BGA package will melt. Pick up the package with a Tweezer of using vacuum pick-up.

Soldering BGA

Again the most common practice to solder BGA is hot air. Here are the steps to solder BGA Package using Hot Air:
Once the BGA Package is removed, clean the pad and remove any excess solder from the board.
  • Apply Flux Paste (Not Liquid Flux) on to the pad. Paste flux will help solder balls to stick so that they do not fall or change position.
  • Place solder balls very carefully on the pad.
  • Apply paste flux to the bottom (soldering side) of the BGA package.
  • Carefully place the BGA Package of the solder balls.
  • Preheat and then apply Hot Air from both top and bottom.
  • Solder balls will melt and get soldered.
BGA technology and the BGA soldering is very reliable if done using the correct procedure. A BGA has less resistance to heat and hence there is lesser or no damage due to overheating.

Benefits / Advantages of Surface Mount Technology (SMT) Over Through-Hole

Surface mount components are small and can be mounted on either side of the PCB and have gained widespread usage in electronics. The benefits of SMT or Surface Mount Technology are available in both design and manufacturing.
SMT

Design Benefits of Surface Mount Technology

Among the most important design-related benefits are significant savings in weight and real estate and electrical noise reduction. A Surface Mount Component can weigh as little as one-tenth of their conventional thru-hole counterparts. This causes a significant reduction in weight of the Surface Mount Assembly (SMA). Because of their smaller size, surface mount components occupy only about one-half to one-third of the space on the printed circuit board.
Since all electronic components are not available in surface mount, the actual area savings on a board will depend on the percentage of through-hole components replaced by surface mount components. Depending on the component mix, the three types of surface mounting discussed in my previous article provide different levels of benefits.
SMT also provides improved shock and vibration resistance as a result of the lower mass of components. Shorter lead lengths of Surface Mount Components offer benefits of lower parasitic that reduces propagation delays and reduces package noise.

Manufacturing Benefits of Surface Mount Technology

In addition to design benefits, SMT also provides many manufacturing benefits. These benefits include reduced board cost, reduced material handling cost, and a controlled manufacturing process. Routing of traces is reduced, size of the board is reduced, and number of drilled holes is also reduced. A smaller board with fewer drilled holes will naturally cost less. If the functions on the surface mount board are not increased, the increased inter-package spacings made possible by smaller surface mount components and a reduction in the number of drilled holes may also reduce the number of layer counts in the printed circuit board. This will again lower the board cost.
The above benefits of Surface Mount Technology don’t necessarily means that SMT assembly will always cost less. It depends when and how SMT is used.

How to Make a Circuit Board

Making or manufacturing a circuit board involves several complex processes.

  • Photoengraving: Under this process a mask or photomask is combined with chemical etching to subtract the copper areas from the circuit board substrate. The photomask is created with a photo plotter design using a CAD PCB software program. Photomasks are also created using a laser printer.
  • Lamination: Multi-layer printed circuit boards are made up of multiple layers consisting of several thin etched boards or trace layers and are bonded together through the process of lamination.
  • Drilling: Each layer of the printed circuit board requires the ability of one layer to connect to another; this is achieved through drilling small holes called “VIAS”. Drilling is mostly done with the use of an automated computer-driven drilling machine.
  • Solder plating: Pads and lands where electronic components are to be soldered on the circuit board are plated to allow soldering of electronic components. Bare copper is not easily solderable. It requires the surface to be plated with a material that facilitates soldering. Earlier lead based tin was used to plate the surfaces, but with RoHS (Restriction of Hazardous Substances) compliance enacted newer lead-free materials such as nickel and gold are now used for plating.
  • Testing the circuit board: Prior to assembly of electronic components on to the board, it needs to be tested. This testing can be done using nails tester, flying probe tester are other computer-operated circuit board testing equipments.
PCB

PCB Design Rules

Layer Process Vs Standard Size
  • Minimum trace / space: 7 mils
  • Minimum via / hole size: 14 mils
  • Minimum pad for plated hole / vias: 26 mils
  • Minimum plated slot: 32 mils
  • Minimum solder mask Clearance: 4 mils
  • Minimum silkscreen Clearance: 4 mils
  • Minimum silkscreen line width: 6 mils
  • Minimum board copper/edge margin: 10 mils

Active and Passive Electronic Components

There are two classes of electronic components – Active and Passive. Both these electronic components are different from each other. This article explains all about active and passive electronic components and the difference between the two.

What are Active Electronic Components?

Active electronic components are those that can control the flow of electricity. Most electronic printed circuit boards have at least one active component. Some examples of active electronic components are transistors, vacuum tubes, silicon-controlled rectifiers (SCRs).

What are Passive Electronic Components?

Passive electronic components are those that don’t have the ability to control current by means of another electrical signal. Examples of passive electronic components are capacitors, resistors, inductors, transformers, and diodes.
Electronic Components

  • What is a Resistor?

A Resistor is an electrical device that resists the flow of electrical current. It is a passive deviceused to control, or impede the flow of, electric current in an electric circuit by providing resistance, thereby developing a drop in voltage across the device.
  • What is a Capacitor?

A capacitor is a passive electrical component that can store energy in the electric field between a pair of conductors called “plates”. The process of storing energy in the capacitor is known as “charging”. The ability of a capacitor to store charge is measured by its capacitance. Capacitors are used in electronic circuits as energy storage devices. They are also be used to differentiate between high-frequency and low-frequency signals. A wide variety of capacitors are available, including  electrolytic capacitors, basic parallel-plate capacitors, and mechanical variable capacitors.
  • What is a Diode?

A diode is a one-way valve for electricity. Diodes allow flow of electricity in one direction. Most diodes have a painted line on one end showing the direction or flow. The negative side is normally white.
  • What is an Integrated Circuit (IC)?

Integrated Circuits are package of several complex circuits. ICs are available in a wide variety of packages and sizes. Their applications are as varied as their packages.
  • What are Transistors?

A transistor is a semiconductor device. It is the fundamental building block of the circuitry in mobile phones, computers, and several other electronic devices. A transistor has very fast response and is used in a number of functions including voltage regulation, amplification, switching, signal modulation, and oscillators. Transistors may be packaged individually or they can be a part of an integrated circuit. Some of the ICs have billion of transistors in a very small area.

Electronic Components

Electronic components, both active and passive, are lifeline of any printed circuit assembly. They both play vital roles in the functioning of any electronic device. Electronic Components are intended to be connected together, usually by soldering to a printed circuit board (PCB), to create an electronic circuit with a particular function.

2017年8月1日星期二

How to Solder – Hand Soldering Tutorial

Hand soldering is done during PCB rework in a production unit when a PCB gets rejected or fails the quality pass test. Hand soldering is also done for repairing and servicing printed circuit boards by service centers.

Soldering Tools and Materials Needed for Hand Soldering

Soldering iron or soldering station: You need a good quality soldering iron or temperature controlled soldering station that run on electricity. If you are dealing with ESD-sensitive PCB and electronic components, then you need an ESD-safe soldering station. If you are doing lead-free soldering, you will probably need a temperature controlled soldering iron or soldering station with higher wattage because the melting point of lead-free solder is higher than tin-lead solder. 
Solder wire: For a good solder joint, you need good quality of solder wire. Solder wires are available in tin-lead and Pb-Free compositions in different diameters. 
Other soldering materials: Apart from soldering tools and solder wire, you may also need few other consumables like solder flux, solder paste, braid etc. Chemtronics is a worldwide leader in manufacturer and supply of PCB rework material.
Once you are ready with all the tools and equipments needed for hand soldering, you are ready to start the job. Start by making sure the PCB and the leads of the electronic components are clean and free from any contamination such as dust or grease. PCB or electronic components which are not clean may have deposited oxides that can lead to bad solder joint. Apply a good quality solder flux on the area of the PCB to be soldered and on to the leads of the components. Flux will help to remove any deposited oxides from the surface of the metals thus leading to better solder joints. You can use a flux pen to dispense flux.
Hand Soldering

Doing Hand Soldering

Now is the time to solder.
Make sure the soldering iron is hot. Do not touch it.
Hold the soldering iron properly in one hand and solder wire in the other hand. Maintain proper angle between the two. Try to use a solder wire reel stand that holds the reed of the wire so that you can pull the wire properly.
Place the solder wire at the point where the lead of the electronic components meets the copper track on the PCB.
Apply heat at the point where solder wire touches the lead of the component.
Once done, remove the soldering iron.
Cut extra leads of the electronic components.
A good solder joint should look shiny. Dull solder joint suggests something is wrong. If you are doing lead-free soldering, the joint will look dull in any case.

The Chinese PCB manufacturing is losing the advantage of low price

As basic components in the electronic information industry chain, PCB is known as the “mother of the electronic products”. According to the distribution map of electronics industry, it is obvious that the development of PCB industry is the same speed of the development of mainland China. And we can see the progress of PCB industry everywhere.

pcb-fabrication.jpg

The data shows that China is still the largest PCB manufacturing in the world. And in the year of 2014, the total value of out-put of PCB was up to $57.437 billion, year-on-year growth was 2.3%. $26.1 billion was maked by Chinese PCB manufacturing,which had the fastest year-on-year growth in the world. The total of China’s PCB domestic and foreign funds accounted for 45% of the total of whole world funds. It is a obvious advantage of Chinese PCB manufacturing. Though, China’s manufacturing industry has been expected for a long time, its performance is poor, and the skill of it is still in the middle and lower reaches of position, it can not get rid of a  “Generation of labor power” label.

Expecially there are many countries like India, the Philippines, Indonesia and Thailand are emerging their PCB industry markets, and the price of PCB raw material is on the rise. What’s worse, China is going to strengthen the ability of Environmental protection and energy saving control. The PCB manufacturing of China is losing the advantage of low price, the same as speed and quality.

There has a factor that can not be ignored is that PCB industry in China is mainly covered in mid-range part. The product type of China not only single but also lacking innovation, which leads to a big gap with the developed countries. Although demands for all kinds of circuit boards have increased, the growth of the soft board, IC load board still lags behind of Japan, South Korea and Taiwan.